Knowledge base · Technical article

UFO High Bay Wattage by Mounting Height: What Actually Sets the Number

Wattage is a result, not a starting point. For a target illuminance the fixture count follows N = (E × A) / (Φ × CU × MF), and mounting height changes the beam angle and the spacing, not the wattage. Typical practice lands around 60–150 W at 4–6 m, 120–240 W at 6–12 m and 240 W upward above 12 m, all conditional on the lux target and the layout.

Updated 2026-11-09·7 min read·BOWI Lighting

Why do wattage-by-height tables mislead?

A table that says “150 W for 20–30 ft” is a rule of thumb carrying a hidden assumption set: a target illuminance, a spacing, a utilisation factor and a maintenance factor. Change any one of them and the number is wrong. Two fixtures of the same wattage can differ by a factor of two in delivered light, because system efficacy spans roughly 100 to more than 230 lm/W. A 150 W fixture at 110 lm/W emits about 16,500 lm; at 200 lm/W it emits 30,000 lm. The lighting result follows lumens, optics and layout, never the wattage on its own.

Height matters for a different reason: it sets the angle at which light reaches the task, and how far apart fixtures can be before uniformity collapses. Doubling mounting height without changing the optic quarters the illuminance on the floor and forces tighter spacing for the same uniformity, so the fixture count changes even at constant wattage.

What actually determines how many fixtures you need?

The lumen method: N = (E × A) / (Φ × CU × MF). E is the maintained illuminance on the working plane, A the area, Φ the luminaire’s delivered lumens, CU the utilisation factor — how much of that flux reaches the plane, from room index, reflectances and optic — and MF the maintenance factor, covering lumen depreciation and dirt. Spacing-to-height ratio is then SHR = (1/Hm) × sqrt(A/N), compared against the luminaire’s published maximum.

A worked example, for layout checking only: a 1,000 m² open warehouse at 150 lx, with a 150 W high bay delivering 24,000 lm, CU 0.65 and MF 0.80. N = (150 × 1,000) / (24,000 × 0.65 × 0.80) = 12.02, so twelve fixtures, which deliver 149.8 lx — 0.2 % under the target; thirteen is the conservative reading. Twelve gives 83 m² per fixture, spacing about 9.1 m, and at a 9 m mounting height above the floor SHR is about 1.0 — inside the range of a 90° optic. Raise the target to 300 lx and the count doubles; drop MF to 0.70 for a dusty plant and it rises again.

This is an estimate for checking a proposed layout, not a design. A DIALux or Relux calculation is what proves uniformity, glare and the effect of racking; the formula alone cannot.

Mounting height, beam angle and the wattage band it implies

Mounting height against optic and practical wattage band
Mounting height above floorBeam angleTypical spacing (S/H)Wattage band seen in the marketWhere it fits
4–6 m90–120°1.0–1.560–150 WLow bay, workshop, retail back-of-house, low warehouse
6–9 m90°0.9–1.2120–200 WGeneral warehouse, packaging, assembly
9–12 m60–90°0.8–1.0150–240 WHigh-bay warehouse, loading bays, manufacturing
12–18 m45–60°0.6–0.9200–300 W, or several rows of lower outputLarge sheds, heavy industry, tall clear height
Above 18 m30–45°, or narrow aisle optics0.5–0.8300 W and above, or linear arraysShipyards, steel, very high clear height

Note: The wattage bands describe what the market offers, not a specification. What governs is maintained illuminance on the task and the uniformity achieved; the same 150 W product can serve 6 m or fail at 12 m depending on optic, spacing and target.

Why rack aisles are a different problem

In a racked warehouse the task is not the open floor; it is the face of the racking and the label on a pallet at 2–6 m. Wide-distribution UFOs mounted over the aisle centre spill light onto the tops of the racks and leave the lower picking faces in shadow. Aisle optics with 30–60° distribution, symmetric or asymmetric, put light down the aisle where the labels are. BS EN 12464-1’s storage rows are modest — in the order of 100 lx for bulk storage, 200–300 lx where picking and label reading are continuous — but the uniformity requirement, around U0 0.4 for storage and 0.6 on task areas, is what fails when a wide beam is used between racks.

Two alternatives work where a round beam does not: light the rack face deliberately with linear luminaires at each level, or use a dedicated aisle optic. Where the aisle is narrow and the ceiling low, a linear high bay is usually easier to aim than a UFO.

UFO or linear high bay?

Form factor against the space it has to light
CriterionUFO high bayLinear high bay
Best mounting height6 m and above4–10 m, and low clear height
OpticsRound symmetric 60–120°; aisle versions availableAsymmetric, aisle and rack-face distributions
Rack aislesWorks with a dedicated aisle optic, poor with a wide round beamBetter control down the aisle and onto rack faces
Glare at low heightHigh with 120° at 4–5 m; needs a diffused optic or lower outputLower surface brightness spread over a longer area
MaintenanceSingle point, lift accessMore fixtures, but reachable from a platform
Best fitOpen floor, high clear height, general lightingRacked aisles, long runs, low-to-medium height

Note: Neither form factor is universally better; the geometry of the space decides. A round beam in a 3 m aisle and a linear fixture in a 15 m open bay are both expensive mistakes.

What else fails at height

  • —Lumen depreciation: design with L70 or L80 data at the ambient temperature at the fixture, not the 25 °C laboratory figure.
  • —Driver temperature: an unheated warehouse in summer can exceed the driver’s rated ambient; derating is a lighting problem, not only a warranty problem.
  • —Surge and voltage: high-bay circuits in industrial buildings see switching transients; specify surge protection at the driver.
  • —Glare for forklift drivers: a 120° beam at 5 m puts the source directly in the driver’s field of view; glare limits apply to the task, not only to offices.
  • —Flicker: check the driver’s output ripple where bar-code scanners, cameras or rotating machinery are present.
  • —Controls: occupancy sensing in aisles saves more than dimming an open floor; make sure the sensor is rated for the mounting height.
  • —Emergency lighting: egress lighting is a separate calculation, not a dimmed high bay.
  • —Maintenance access: a 12 m mounting height needs a lift or a lowering mechanism; plan it before the fixtures are chosen.

Five numbers to ask for before accepting a layout

  • —Maintained illuminance on the stated working plane, and the maintenance factor used to reach it.
  • —Uniformity U0 (minimum divided by average) at the same plane, taken from a calculation file rather than a claim.
  • —Delivered lumens to LM-79, and the lumen maintenance data behind the MF.
  • —Beam angle and the maximum spacing-to-height ratio for the optic actually supplied.
  • —UGR or glare classification at the real mounting height, plus the driver’s rated ambient temperature.

Three misjudgements worth correcting early

  • —“Wattage follows height.” Height follows the layout; wattage follows the lumens needed after CU and MF. A 240 W fixture with a narrow beam can put less useful light on a picking face than two 120 W aisle fixtures.
  • —“More wattage means a brighter floor.” It means more flux out of the fixture. Whether that flux lands on the task depends on the optic and the spacing; past a point, extra wattage buys glare rather than illuminance.
  • —“UFO is always the high-bay answer.” In a 5 m rack aisle, a linear fixture aimed at the rack face usually beats a round beam from above.
Selection Q&A

Questions engineers ask

How many watts does a UFO high bay need at 10 m?

There is no single number. At 9–12 m, 150–240 W with a 60–90° optic is the common band, but the answer comes from N = (E × A)/(Φ × CU × MF) against your target lux, spacing and maintenance factor. Two 150 W products with different efficacy can differ by 50 % in delivered light.

What beam angle should a warehouse high bay use?

90° for general open floor at 6–9 m; 60–90° at 9–12 m; 30–60° aisle optics where light must travel down a rack aisle. A 120° beam suits low ceilings and wide open areas, and becomes a glare source above about 6 m.

How many high bays per square metre?

Work it from the lumen method rather than a density rule. A 1,000 m² area at 150 lx with 24,000 lm fixtures, CU 0.65 and MF 0.80 needs about twelve fixtures, roughly one per 83 m². At 300 lx the same area needs about twenty-four.

Is a UFO high bay suitable for rack aisles?

Only with an aisle optic. A wide round beam lights the rack tops and leaves the picking faces dark; a 30–60° distribution aimed down the aisle is the usual answer, or linear luminaires at each rack level.

What maintenance factor should be used?

It depends on the environment. A clean, air-conditioned space might use 0.85–0.90 with good lumen maintenance; a dusty plant or a cold store with wide temperature swings should use a lower figure and verified LM-80 data. The MF has to include both dirt and depreciation, and it has to be stated in the calculation.